Rocky Point sits in Pender County along US 117 near I 40, a rural community of larger lots, farms and workshops. People here use their land. They need long driveways, shop floors, barn pads and room for trucks and trailers. Good concrete makes that work easier.
Coastal Concrete Wilmington is a locally owned concrete company in Rocky Point NC. We pour slabs, driveways and pads, and we give a free written estimate before work starts.
Concrete for rural lots in Rocky Point
Rocky Point customers ask for long driveways, workshop slabs, pole barn floors and pads for equipment and RVs. We pour them thick enough for trucks and tractors and on a base that will not wash out. A concrete company in Rocky Point NC has to plan for heavy loads.
We also pour patios, walks and steps for the house.
- Long driveways and gate aprons
- Shop and barn slabs
- Pads for RVs, tanks and equipment
- House patios, walks and steps
Soil, drainage and open land
The ground near Rocky Point is a mix of sand and clay, with low spots that hold water. Slabs on open land need drainage, since runoff can cut into a base. We compact crushed stone, add steel and slope slabs and drives so water leaves.
Wind and heat can dry concrete fast on open land, so we pour early and cure carefully.
Repairs and farm slabs
Older farm slabs often have cracks and sunken spots. We repair many of them, lift low areas and replace panels that have failed. See concrete repair, concrete leveling and concrete demolition.
We tell you honestly when a repair will do.
Start your Rocky Point project
Call us any day from 5 AM to 10 PM or use the contact page. We will visit, measure and give you a free written estimate.
Work on a rural lot should be done once. A concrete company in Rocky Point NC who plans for load and water gives you that. We serve Rocky Point and the roads around it.
Questions about hiring a concrete company in Rocky Point NC
Do you travel to Rocky Point for concrete jobs?
Yes. Rocky Point is about a half hour north of our shop in the 28409 area, and we serve it regularly. We visit your property for a free estimate, measure the work and talk through the plan. For larger jobs, the trip is a small part of the cost.
Call us any day from 5 AM to 10 PM, give us your address and describe the job. If you are out in the country, we ask for landmarks and gate details, so our crew can find you and bring the right equipment. We also check access for concrete trucks, since long dirt roads and soft ground can be a problem after rain.
Send the barn size and the heaviest vehicle on the phone, and a concrete company in Rocky Point NC can give you a clear starting price. Ask us to meet you at the gate for the first visit.
How thick should a farm shop floor be?
A light workshop floor can be four or five inches thick. A shop with tractors, trucks, lifts or heavy tools should be five to six inches, with steel. Areas that hold heavy machine feet or a vehicle lift may need to be thicker.
Thickness works with the base and the steel. On sandy or clayey ground, we prepare the base so the slab sits on even support. We also add a vapor barrier, so moisture does not rise through the floor. We ask what you will do in the building, then give you a thickness and a written price. It costs far less to build the floor right than to fix a cracked one.
Tell us the weight of your tank or generator, and we will size the thickness and the steel for it. Tell us about your well, your septic system and any buried lines, and a concrete company in Rocky Point NC will keep trucks and new concrete well clear of them.
Can you pour a pad for a water tank or a generator?
Yes. A tank pad must be strong and level, since a full tank is very heavy. A generator pad needs to be flat, with space for service and air flow. We pour both with steel and a firm base, and we slope the surface slightly so water runs off.
We ask for the size and weight of the tank or generator, plus any rules from the maker or the county. See concrete pads. We also plan for pipes, wires and sleeves that go through the slab. A clear sketch and a written price come with the estimate.
A few photos of the entrance and the gate help us plan the trucks, and they save time on pour day. A concrete company in Rocky Point NC should plan for soft ground after rain, so we watch the forecast, test the road and may delay a pour until the lot is firm.
How do you protect a long driveway from washing out?
Water is the problem on long rural drives. We plan the slope so water leaves the drive in many small places instead of gathering in one. We add culverts or drain pipes where water crosses. We also thicken the edges, where erosion starts, and compact the shoulders.
At the road, we look at how the drive meets the county or state road, since rules and slopes matter there. A good plan includes where the water goes after it leaves the concrete. We walk the drive with you, mark the low spots and write down the plan. A little work on drainage can protect the drive for many years.
Mark the problem cracks with chalk before we visit, and we can price each repair quickly and clearly. Ask us how we pour a barn or shop floor in sections, since large floors need planned joints, enough crew and a steady supply of concrete from the plant.
Can I pour my own slab and have you do only the finishing?
Sometimes, but we usually do not recommend it. A slab is a team job. Timing, base work, steel and finishing all depend on each other. If one part is wrong, the whole slab can suffer. Concrete does not wait for anyone, and a mistake on pour day cannot be undone.
If you want to save money, there are smarter ways. You can clear the site, or remove old concrete, to lower the price. We can talk through what you can safely do and what we should handle. A free estimate tells you the cost of the whole job and which parts you could help with.
A budget talk early on helps us suggest smart ways to build a long driveway in stages. Share your thoughts on future buildings, and we will leave stub outs, thicker edges or extra room so a new slab can tie into this one without cutting it apart.
How should I plan for trucks on my gravel road?
Concrete trucks are large and heavy, and they need room to turn and a firm road. A soft or narrow gravel road can be a problem. We ask about the route, the gates and the turns. If the road is rough, we may use a pump truck from a distance or add gravel before the pour.
Give us a few landmarks when you call. We may ask for photos of the road and the gate. This helps us plan the day and avoid delays. We also tell you how long the trucks will be on site. A little planning at the start saves time and money, and keeps your road in better shape after the pour.
Plans or sketches help, and a concrete company in Rocky Point NC can work from either to give you a firm number. Ask us about a written plan for stages, since a concrete company in Rocky Point NC can break a large project into steps that match your budget.
Looking for a concrete company in Rocky Point NC? Call (910) 981-2124 any day from 5 AM to 10 PM, or use the estimate form. Coastal Concrete Wilmington is locally owned and gives clear written estimates for patios, driveways and slabs.